丁康康,逄昆,顾良华,张彭辉,侯建,孙明先.几种典型金属材料西沙海洋全浸区腐蚀行为规律研究[J].装备环境工程,2019,16(4):65-71. DING Kang-kang,PANG Kun,GU Liang-hua,ZHANG Peng-hui,HOU Jian,SUN Ming-xian.Corrosion Behavior of Typical Metal Materials in Xisha Marine Immersion Zone[J].Equipment Environmental Engineering,2019,16(4):65-71. |
几种典型金属材料西沙海洋全浸区腐蚀行为规律研究 |
Corrosion Behavior of Typical Metal Materials in Xisha Marine Immersion Zone |
投稿时间:2018-11-06 修订日期:2019-04-25 |
DOI:10.7643/ issn.1672-9242.2019.04.012 |
中文关键词: 金属 西沙 全浸区 腐蚀 |
英文关键词:metal Xisha areas immersion zone corrosion |
基金项目: |
|
Author | Institution |
DING Kang-kang | State Key Laboratory for Marine Corrosion and Protection, Luoyang Ship Material Research Institute, Qingdao 266237, China |
PANG Kun | State Key Laboratory for Marine Corrosion and Protection, Luoyang Ship Material Research Institute, Qingdao 266237, China |
GU Liang-hua | State Key Laboratory for Marine Corrosion and Protection, Luoyang Ship Material Research Institute, Qingdao 266237, China |
ZHANG Peng-hui | State Key Laboratory for Marine Corrosion and Protection, Luoyang Ship Material Research Institute, Qingdao 266237, China |
HOU Jian | State Key Laboratory for Marine Corrosion and Protection, Luoyang Ship Material Research Institute, Qingdao 266237, China |
SUN Ming-xian | State Key Laboratory for Marine Corrosion and Protection, Luoyang Ship Material Research Institute, Qingdao 266237, China |
|
摘要点击次数: |
全文下载次数: |
中文摘要: |
目的 研究几种典型金属材料在西沙海洋全浸区的腐蚀行为规律。方法 通过外场暴露试验,分析EH36和CM690船用钢、316L不锈钢以及5083铝合金材料暴露0.5、1、2 a后的腐蚀形貌与动力学规律。结果 CM690腐蚀速率要大于EH36,而点蚀深度规律相反。316L不锈钢发生较为严重缝隙腐蚀,5083铝合金则以局部腐蚀为主。结论 试验条件下,EH36与CM690钢腐蚀质量损失与点蚀最为严重,316L不锈钢与5083铝合金生物污损严重,伴有局部腐蚀。 |
英文摘要: |
Objective To investigate corrosion behaviors and rules of typical metal materials in Xisha marine immersion zone. Methods Field exposure test was carried out on marine steels of EH36 and CM690, 316L stainless steel as well as 5083 aluminium alloy materials at Xisha for 0.5 a, 1 a and 2 a. After samples were retrieved, the corrosion morphology characteristics and kinetics rules were analyzed. Results The corrosion rate of CM690 was higher than that of EH36, while the rule was opposite for the pitting depth; serious crevice corrosion occurred on 316L stainless steel, and it was mainly local corrosion for 5083 aluminum alloy. Conclusion Under the test conditions, the corrosion weight loss and pitting corrosion of EH36 and CM690 steel are the most serious; the biofouling of 316L stainless steel and 5083 aluminum alloy is severe, accompanied by local corrosion. |
查看全文 查看/发表评论 下载PDF阅读器 |
关闭 |
|
|
|