刘永亮,任克亮,马旭轮,张基明.平面四杆机构在舰载垂直发射装置舱口盖系统中的应用分析[J].装备环境工程,2019,16(5):13-17. LIU Yong-liang,REN Ke-liang,MA Xu-lun,ZAHNG Ji-ming.Application of Plane Four Poles Mechanism in Hatch Opening System of Ship Vertical Launcher[J].Equipment Environmental Engineering,2019,16(5):13-17.
平面四杆机构在舰载垂直发射装置舱口盖系统中的应用分析
Application of Plane Four Poles Mechanism in Hatch Opening System of Ship Vertical Launcher
投稿时间:2018-11-03  修订日期:2019-05-25
DOI:10.7643/ issn.1672-9242.2019.05.004
中文关键词:  平面四杆机构  舱口盖开盖系统  舱口盖开盖解锁机构  曲柄摇杆机构  舰载垂直发射装置
英文关键词:plane four poles mechanism  hatch opening system  hatch opening and unlocking mechanism  brace and rocker mechanism  ship vertical launcher
基金项目:
作者单位
刘永亮 中国船舶重工集团公司第七一三研究所,郑州 450015 
任克亮 中国船舶重工集团公司第七一三研究所,郑州 450015 
马旭轮 中国船舶重工集团公司第七一三研究所,郑州 450015 
张基明 中国船舶重工集团公司第七一三研究所,郑州 450015 
AuthorInstitution
LIU Yong-liang 713 Research Institute of China Shipbuilding Industry Corporation, Zhengzhou 450015, China 
REN Ke-liang 713 Research Institute of China Shipbuilding Industry Corporation, Zhengzhou 450015, China 
MA Xu-lun 713 Research Institute of China Shipbuilding Industry Corporation, Zhengzhou 450015, China 
ZAHNG Ji-ming 713 Research Institute of China Shipbuilding Industry Corporation, Zhengzhou 450015, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 研究在舰载垂直发射装置舱口盖系统中设计平面四杆机构的方案的可行性与可靠性。方法 提出舱口盖开盖系统设计方案,建立平面四杆机构开盖模型,进行理论分析与计算,建立ADAMS动力学仿真模型,对曲柄摇杆机构进行仿真分析,并与理论计算值进行对比。进行30~90 kg负载试验,计算舱口盖开盖的角度和时间。结果 舱口盖开盖解锁机构各构件的长度及电机的开盖扭矩应不小于569 N•m,转速应小于10 r/min。电机的开盖扭矩值应不小于509 N•m,复核复算结果基本一致。舱口盖开盖的角度应大于93°,开盖时间为2.8 s,满足要求。结论 验证了方案的可行性,为其他垂直发射装置的舱口盖设计提供了工程经验。
英文摘要:
      Objective To research the feasibility and reliability of scheme for designing plane four poles mechanism for hatch system of ship vertical launcher. Methods The hatch opening system scheme was proposed according to the opening angle and time index in ship vertical launcher. The four poles mechanism model was built for theoretical analysis and calculation. An ADAMS dynamic model was built to simulate the crank and rocker mechanism and compare with the calculated value. The 30-90 kg load test was carried out to calculate the angle and time of hatch opening. Results The hatch torque should not be less than 569 N•m, and speed should be less than 10 r/min. The cover opening torque of the motor should not be less than 509 N•m. The review result was basically consistent. The opening angel should be larger than 93° and the opening time should be 2.8 s. The requirements were met. Conclusion The scheme feasibility is verified. It provides engineering experiences for design of hatch for vertical launcher.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第13522571位访问者    渝ICP备15012534号-5

版权所有:《装备环境工程》编辑部 2014 All Rights Reserved

邮编:400039     电话:023-68792835    Email: zbhjgc@163.com

视频号 公众号