Problem of Measurement Distortion Caused by Impact Sensor Installation

YANG Weiyuan; YANG Zhengxi; HU Junqi; ZHANG Xin

doi:10.7643/issn.1672-9242.2026.04.013

PDF(1712 KB)

Equipment Environmental Engineering ›› 2026, Vol. 23 ›› Issue (4) : 134-143. DOI: 10.7643/issn.1672-9242.2026.04.013

Aviation and Aerospace Equipment

Problem of Measurement Distortion Caused by Impact Sensor Installation

YANG Weiyuan^1,2, YANG Zhengxi¹, HU Junqi¹, ZHANG Xin¹

Author information +

History +

Abstract

Aiming at the problem of distortion caused by sensor installation in impact measurement, simulation and comparative tests on impact of different mounting blocks are carried out. The impact response spectrum SRS and energy spectrum ESD analysis are carried out on the measured data of sensors with mounting blocks of different specifications. The analysis and simulation results show that the impact of mounting blocks on the impact measurement is related to the material and size of mounting blocks, and the overall resonance frequency of flat mounting blocks and sensors is higher, which has no significant impact on the impact measurement. However, the commonly used cube mounting blocks with a side length of 10 mm and thin and tall mounting blocks have obvious distortion in the high frequency band of 5 000-10 000 Hz; The experimental results are consistent with the simulation results. The research results have guiding significance for impact measurement installation.

Key words

shock / piezoelectric sensor / installation / simulation / distortion

Cite this article

EndNote

Ris (Procite)

Bibtex

Download Citations

YANG Weiyuan, YANG Zhengxi, HU Junqi, ZHANG Xin. Problem of Measurement Distortion Caused by Impact Sensor Installation[J]. Equipment Environmental Engineering. 2026, 23(4): 134-143 https://doi.org/10.7643/issn.1672-9242.2026.04.013

References

[1] 杨蔚原, 孙建亮, 任杰安. 振动试验技术疑难解析[M]. 北京: 中国宇航出版社, 2023.
YANG W Y, SUN J L, REN J A.Analysis of Technical Difficulties in Vibration Test[M]. Beijing: China Aerospace Press, 2023.
[2] 尹钊, 余抗, 赵波. 不同材料安装底座对冲击传感器灵敏度影响试验研究[J]. 航天器环境工程, 2021, 38(1): 51-54.
YIN Z, YU K, ZHAO B.The Effect of Different Materials Used for Installation Base on the Sensitivity of Shock Sensor[J]. Spacecraft Environment Engineering, 2021, 38(1): 51-54.
[3] 孙璟, 侯金瑛, 丁沛, 等. 传感器安装对爆炸冲击测试结果影响的试验研究[J]. 宇航总体技术, 2022, 6(6): 30-37.
SUN J, HOU J Y, DING P, et al.Experimental Study on the Influence of Sensor Installation on Explosion Impact Test Results[J]. Astronautical Systems Engineering Technology, 2022, 6(6): 30-37.
[4] 高鹏, 郭涛, 夏烈芳. 不同安装基座下冲击信号的冲击响应谱研究[J]. 通信技术, 2010, 43(4): 211-213.
GAO P, GUO T, XIA L F.Study on Shock Response Spectrum of Impact Signal under Different Installation Base[J]. Communications Technology, 2010, 43(4): 211-213.
[5] 张洁文, 秦敏, 刘科, 等. 冲击传感器不同安装方式对校准结果的影响分析[J]. 计测技术, 2016, 36(1): 46-49.
ZHANG J W, QIN M, LIU K, et al.Effect Analysis of Shock Sensors on Calibration Based on Different Installation Modes[J]. Metrology & Measurement Technology, 2016, 36(1): 46-49.
[6] 于雪莲. 加速度传感器安装方式对灵敏度的影响[J]. 中国计量, 2017(2): 114-116.
YU X L.Influence of Installation Mode of Acceleration Sensor on Sensitivity[J]. China Metrology, 2017(2): 114-116.
[7] 涂骥. 振动传感器的选择与安装[J]. 计量与测试技术, 2010, 37(1): 45-46.
TU J.Choice and Installation of the Vibration Transducer[J]. Metrology & Measurement Technique, 2010, 37(1): 45-46.
[8] 陈爽, 孙浩, 冯超, 等. 加速度传感器及其安装工艺对碰撞模拟试验结果的影响[J]. 汽车工程, 2012, 34(11): 1033-1038.
CHEN S, SUN H, FENG C, et al.The Effects of Accelerometer and Its Mounting Technique on the Results of Crash Simulation Test[J]. Automotive Engineering, 2012, 34(11): 1033-1038.
[9] RAO M V R M, RAO K R M. Measurement and Analysis of Shock Acceleration[J]. Journal of Sound and Vibration, 1980, 68(2): 257-267.
[10] VAROTO K G, MCCONNELL. Finite Element Modeling for the Dynamic Response of a Mounted Accelerometer[C]. Proceedings of the 16th International Modal Analysis Conference, Santa Barbara, USA. 1998, 1: 608-614.
[11] ISLAM A M MT, STARR A, XU B. Uncertainty in Shock Measurements Due to Sensor Mounting Conditions: A Numerical and Experimental Study[J] Mechanical Systems and Signal Processing, 2020, 144: 135-144.
[12] 丰雷, 马铁华. 高冲击加速度传感器横向效应及装配方式所致测试误差[J]. 振动与冲击, 2014, 33(20): 198-201.
FENG L, MA T H.Transverse Effect on Sensitivity of High Impact Accelerometer and Measurement Error Caused by Mounting of Accelerometer[J]. Journal of Vibration and Shock, 2014, 33(20): 198-201.
[13] 赵小龙, 马铁华, 范锦彪. 高g值加速度计在高冲击下的失效特性的研究[J]. 传感技术学报, 2012, 25(12): 1668-1672.
ZHAO X L, MA T H, FAN J B.The Study of Failure Characteristic of High g Acceleration in High Shock[J]. Chinese Journal of Sensors and Actuators, 2012, 25(12): 1668-1672.
[14] 房远勇, 吴健, 杨克辛, 等. 一种导致压电式冲击传感器零漂原因分析及抑制措施[J].宇航计测技术, 2022, 42(4): 43-48.
FANG Y Y, WU J, YANG K X, et al.Analysis of Causes of Zero Drift of Piezoelectric Shock Sensor and Zero Drift Suppression[J]. Journal of Astronautic Metrology and Measurement, 2022, 42(4): 43-48.
[15] 张国伟, 冯顺山, 俞为民. 高冲击过载加速度传感器零漂分析[J]. 华北工学院学报, 2004, 25(1): 64-67.
ZHANG G W, FENG S S, YU W M.Analysis of Zero Drift of the Acceleration Sensor in High-Impulsion and High Overloading[J]. Journal of North China Institute of Technology, 2004, 25(1): 64-67.
[16] GE C F, DUNNO K, SINGH M A, et al.Development of a Drone's Vibration, Shock, and Atmospheric Profiles[J]. Applied Sciences, 2021, 11(11): 5176.
[17] WANG L Q, SHANG F.Effect of Sensor Installation Angle on Measurement of Explosion Shock Wave Pressure[J]. Measurement Science and Technology, 2022, 33: 11.
[18] 李群. (振动与冲击传感器)基座应变灵敏度测试方法的研究[J]. 中国质量与标准导报, 2019(8): 58-61.
LI Q.(Vibration and Shock Sensor) Research on Test Method of Base Strain Sensitivity[J]. China Standards Review, 2019(8): 58-61.
[19] 卢来洁, 马爱军, 冯雪梅. 冲击响应谱试验规范述评[J]. 振动与冲击, 2002, 21(2): 18-20.
LU L J, MA A J, FENG X M.A Review of Shock Response Spectrum Test Standard[J]. Journal of Vibration and Shock, 2002, 21(2): 18-20.
[20] PATTERSON J D.Measurement Considerations in Pyroshock Measurements[C]/ /Proceedings of the 44th International Instrumentation Symposium.USA: IEEE,1998: 364-372.
[21] 赵联春, 马家驹, 曹志飞, 等. 传感器安装方式对轴承振动测量特性的影响[J]. 轴承, 2003(1): 26-28.
ZHAO L C, MA J J, CAO Z F, et al.The Influence of Installation Manner of Transducer on Vibration Measure Characteristic of Bearings[J]. Bearing, 2003(1): 26-28.
[22] 吴长波, 敬发宪, 崔海涛. 航空发动机振动传感器安装座振动特性数值分析方法[J].燃气涡轮试验与研究, 2013, 26(3): 34-37.
WU C B,GOU F X,CUI H T.Numerical Analysis Method for Vibration Sensor Mounting Housing of an Aero-Engine[J]. Gas Turbine Experiment and Research, 2013, 26(3): 34-37.
[23] 郑星, 黄海莹. 加速度传感器安装方式的理论建模与响应分析[J]. 传感器与微系统, 2016, 35(11): 61-63.
ZHENG X, HUANG H Y.Theoretical Modeling and Response Analysis of Acceleration Sensor Installation Mode[J]. Transducer and Microsystem Technologies, 2016, 35(11): 61-63.
[24] 隋锡阳. 浅析压电式加速度传感器的安装及影响消除[J]. 测控技术, 2016(35): 409-412.
SUI X Y.Analysis on Installation and Efect of Piezoelectric Acceler ation S Ensor[J]. Measurement Control Technology, 2016(35): 409-412.
[25] 闫利军, 赵亚娟, 高志远. 压电加速度传感器在机载测试领域中的安装研究[J]. 电子测量技术, 2014, 37(7): 130-134.
YAN L J, ZHAO Y J, GAO Z Y.Study on Installation of Piezoelectric Acceleration Sensor in the Airborne Test[J]. Electronic Measurement Technology, 2014, 37(7): 130-134.
[26] 唐国明, 杨曙年. 压电式加速度传感器安装谐振频率分析[J]. 传感器与微系统, 2006, 25(7): 24-26.
TANG G M, YANG S N.Analysis of Mounting Resonant Frequency of Piezo-Electric Acceleration Sensor[J]. Transducer and Microsystem Technologies, 2006, 25(7): 24-26.
[27] 黄鑫. 振动试验中传感器安装方法及对比分析[J]. 中国检验检测, 2021, 29(2): 24-26, 5.
HUANG X.Comparison and Analysis of Sensor Installation Methods in Vibration Test[J]. China Inspection Body & Laboratory, 2021, 29(2): 24-26, 5.